types of inductors and their applications pdf

Types of inductors and their applications pdf

File Name: types of inductors and their applications .zip
Size: 17434Kb
Published: 25.05.2021

Air Core Inductors

Basic Electronics - Types of Inductors

Types of Inductors and Applications

Different Types of Inductor and Its Applications

Air Core Inductors

There are different types of inductors. Depending on their material type they are basically categorized as follows. Ceramic is the most commonly used material for inductor cores.

Since ceramic has no magnetic properties, there is no increase in the permeability value due to the core material. Its main aim is to give a form for the coil. In some cases it will also provide the structure to hold the terminals in place. The main advantage of these inductors are very low core losses, high Quality factor.

These are mainly used in high frequency applications where low inductance values are required. Back to top.

In the areas where low space inductors are in need then these iron core inductors are best option. These inductors have high power and high inductance value but limited in high frequency capacity. These are applicable in audio equipments. When compared with other core indictors these have very limited applications.

Ferrite is also referred as ferromagnetic material. They exhibit magnetic properties. They consist of mixed metal oxide of iron and other elements to form crystalline structures. The general composition of ferrites is XFe 2 O 4. Where X represents transition materials. Mostly easily magnetized material combinations are used such as manganese and zinc MnZn , nickel and zinc niZn. Ferrites are mainly two types they are soft ferrites and hard ferrites.

These are classified according to the magnetic coercivity. Coercivity is the magnetic field intensity needed to demagnetize the ferromagnetic material from complete saturation state to zero.

Soft Ferrite These materials will have the ability to reverse their polarity of their magnetization without any particular amount of energy needed to reverse the magnetic polarity.

These are also called as permanent magnets. These will keep the polarity of the magnetization even after removing the magnetic field. Ferrite core inductor will help to improve the performance of the inductor by increasing the permeability of the coil which leads to increase the value of the inductance.

The level of the permeability of the ferrite core used within the inductors will depend on the ferrite material.

This permeability level ranges from 20 to 15, according to the material of ferrite. Thus the inductance is very high with ferrite core when compared to the inductor with air core. These are formed from very fine particles with insulated particles of highly pure iron powder. It gives us a solid looking core when this iron power is compressed under very high pressure and mixed with a binder such as epoxy or phenolic.

By this action iron powder forms like a magnetic solid structure which consists of distributed air gap. Due to this air gap it is capable to store high magnetic flux when compared with the ferrite core. This characteristic allows a higher DC current level to flow through the inductor before inductor saturates.

This leads to reduce the permeability of the core. Thus these inductors posses with high temperature co-efficient stability. These are mainly applicable in switching power supplies. Iron Powder Cores. These core materials are formed by arranging many number of laminations on top of each other. These laminations may be made up of different materials and with different thicknesses. So this construction has more flexibility.

These laminations are made up of steel with insulating material between them. These are arranged parallel to the field to avoid eddy current losses between the laminations. These are used in low frequency detectors. They have high power levels so , they are mostly used at power filtering devices for excitation frequencies above several KHz.

These are wounded on cylindrical bobbin so these are named as bobbin based inductors. These are mainly used for mounting on printed circuit boards. It consist of two types of leads they are axial lead and radial lead. Axial lead means lead exits from both sides of the core for horizontal mounting on PC board. Radial lead means lead exits from both sides of the core for vertical mounting on PC board. These are shown below. Two Bobbin Inductor.

Wire wounded on core which has ring or donut shaped surface. These are generally made up of different materials like ferrite, powdered iron and tape wound etc. This inductor has high coupling results between winding and early saturation. Its arrangement gives minimum loss in magnetic flux which helps to avoid coupling magnetic flux with other devices.

It has high energy transferring efficiency and high inductance values at low frequency applications. These inductors mainly used in medical devices, switching regulators, air conditioners, refrigerators, telecommunications and musical instruments etc.

Toroidal Inductor. The name itself indicates that it consist of multi layers. Simply by adding additional layers of coiled wire that is wound around the central core to the inductor gives multi-layer inductor.

Generally for more number of turns in a wire , the inductance is also more. In these multi-layer inductors not only the inductance of the inductor increases but also the capacitance between the wires also increases. The most advantage of these inductors is by giving the lower operating frequencies also we can get higher inductance results. These are having applications at high frequencies to suppress noise, in signal processing modules like wireless LANs, Bluetooth etc.

These are also used at mobile communication systems. Multi-layer Ceramic Inductors. These uses a film of conductor on base material. Thus according to the requirement this film is shaped for conductor application. Film inductors in thin size are suitable for DC to DC converters that serve as power supplies in smart phones and mobile devices. The Rf thin film inductor is shown below:. Film Inductor. It is formed by moving the magnetic core in and outside of the inductor windings.

By this magnetic core we can adjust the inductance value. When we consider a ferrite core inductor , by moving its core inside and outside on which the coil is wounded , variable ferrite core inductor can be formed.

These type of inductors are used in radio and high frequency applications where the tuning is required. The two conductors connected by electromagnetic induction are generally referred as coupled inductors. We already seen that whenever the AC current is flowing in one inductor produces voltage in second inductor gives us mutual inductance phenomenon. Coupled inductors will work on this phenomenon only.

These can isolate two circuits electrically by transferring impedance through the circuit. A transformer is one of the type of coupled inductor. Coupled Inductors. These inductors or molded by plastic or ceramic insulators. These are typically available in bar and cylindrical shapes with wide option of windings. Your email address will not be published. Air Core Inductor. Molded inductors. Comments I love your explaination but can we be partners …am also an engineer.

Thanks in advance Ndy. Type of inductors, construction, specifications and applications please explain. Leave a Reply Cancel reply Your email address will not be published. Change Ad Consent.

Basic Electronics - Types of Inductors

There are different types of inductors. Depending on their material type they are basically categorized as follows. Ceramic is the most commonly used material for inductor cores. Since ceramic has no magnetic properties, there is no increase in the permeability value due to the core material. Its main aim is to give a form for the coil. In some cases it will also provide the structure to hold the terminals in place. The main advantage of these inductors are very low core losses, high Quality factor.

Types of Inductors and Applications

Gowanda designs and manufactures Bobbin Wound Inductors for a variety of power supply and power conversion applications. A Bobbin Wound Inductor is a inductor that is designed with the coil wound on a coil form or bobbin. The core structure is then mounted to the bobbin.

There are only three basic components in any electronic circuit design- resistor, capacitor, and inductor. We have already covered the introduction to a resistor and its different types , and also covered capacitors and its different configurations. In this tutorial, we are going to know about different types of inductors and how to choose an inductor for different applications. Inductors are often referred to as "AC resistance". The main characteristic of an inductor is its ability to resist changes in current and store energy in the form of a magnetic field.

Different Types of Inductor and Its Applications

There are various types of inductors are available in the market based on its ratings and sizes and ratings. Their physical sizes differ from small sizes to the enormous transformer, based on the AC frequency being used and power being handled. An Inductor is one of the basic electrical components used in much wider application areas namely signal controlling, voltage stabilization, noise elimination, automobile operations, power electronic equipment, etc. At the present time, the designing improvement technique of an inductor enhances major performance on rest of the circuit. An inductor is also termed as a coil, reactor, or choke, is a two-terminal electrical component used to build various electrical and electronic circuits.

An inductor , also called a coil , choke , or reactor , is a passive two-terminal electrical component that stores energy in a magnetic field when electric current flows through it. When the current flowing through the coil changes, the time-varying magnetic field induces an electromotive force e. According to Lenz's law , the induced voltage has a polarity direction which opposes the change in current that created it.

Types of Inductors and Applications

4 comments

  • Grinconvaba 25.05.2021 at 20:47

    Depending on the application there are many types of inductors, they come in various form factors, there are high-frequency inductors.

    Reply
  • Byron L. 29.05.2021 at 04:28

    Sometimes, there isn't a core, in which case it's an air core inductor. In high frequency applications, AC losses often become an issue that must be addressed for.

    Reply
  • Leroy P. 30.05.2021 at 20:37

    Energy efficient buildings with solar and geothermal resources pdf why are you suitable for this job sample answer pdf

    Reply
  • Aaliyah A. 31.05.2021 at 19:20

    Air Core Inductor. Iron Core Inductor. Ferrite Core Inductor. Soft Ferrite. Hard Ferrite. Iron Powder Inductor. Laminated Core Inductor. Bobbin based inductor. Toroidal Inductor. Multi-layer Ceramic Inductors.

    Reply

Leave a reply